Panasonic WV-SW558 Guide d'installation

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number i

10PrecautionsRefer installation work to the dealer.Installation work requires technique and experi-ences. Failure to observe this may cause fire, elec

11Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. Do not touch this product, the power cord or the conne

12About SD memory card • Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on the [SD memory card] tab of “Basic

13Precautions for installationThis product is designed to be installed under eaves.Install the product under eaves to avoid direct sunlight.Installing

14Do not remove or loosen the screws on the rear of this product. If the screws (7 pcs.) are loosened, water expo-sure may cause damage or malfunction

15Major operating controlsEnclosureDome coverTilting tableZoom lock knobFocus ringInner domeTilting lock screw (x2)Azimuth adjustment ringAudio output

16About the [INITIAL SET] buttonAfter turning off the power of the camera, turn on the power of the camera while holding down this button, and wait fo

17When installing the camera on a wall or a ceiling, there are two methods as specified below. • Using a two-gang junction box • Use the supplied

18Using a two-gang junction box • Secure the camera attachment (accessory) to the two-gang junction box built in a wall or ceil-ing using the fixing

19Using the mount bracket (accessory)Note: • When the camera is mounted on the wall or ceiling with a hole for cable running, or the camera is mount

2The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this

20x Determine the direction of the mount bracket according to the installation environment (how the cables are wired, etc.) before mounting it to a w

21<Using a conduit>Align the direction of the conduit to the direction of female thread for the conduit on the mount bracket, and mount the moun

22c In the direction determined in x, fix the camera attachment (accessory) on the mount bracket using the fixing screws. Recommended tightening t

23IMPORTANT: • When inserting a SD memory card, make sure the direction. • Before removing the SD memory card, make sure to select “Not use” for “

24Caution: • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1). Before starting the connect

25x Connect an external amplifier-embedded speaker to the audio output cable (for use of the audio transmission function). SW559 Connect a stereo

26IMPORTANT: • Input and output of the EXT I/O terminal 2 and 3 can be switched by configuring the setting. "Off" is selected by default.

27Waterproof treatment for the cable joint sectionsAdequate waterproof treatment is required for the cables when installing the camera with cables exp

28Connection example when connecting to a network using a PoE hub Powered speaker (option)Powered speaker (option)Microphone (option)Microphone (optio

29z Mount the camera. <Using a two-gang junction box> q Connect each cable. (☞ Page 24) Waterproof the connecting portion. (☞ Page 27) w

3ContentsImportant safety instructions ... 4Limi

30<Using the mount bracket> q Attach the camera onto the camera attachment (accessory) while aligning the "OPEN" mark of the camera w

31 w Engage the camera attachment fixing screws of the camera with the screw hole of the camera attachment (accessory) and rotate the camera in the d

32 t Attach the base cover (accessory) that was removed according the steps in page 19. y Use the bit for tamperproof screw (accessory) to tighten the

33&DPHUDƄ[LQJVFUHZUHG* 7KHFDPHUDƄ[LQJVFUHZVKDOOEHVHFXUHO\WLJKWHQHGv Connect the RCA pin cable to the monitor output connector (☞ page

34z Adjust the camera angle.When determining the camera angle, repeat fine adjustments by gradually moving the panning table, tilting table, and azim

35 <Lens angular field of view (q Angle)>Horizontal: 24.20° (TELE) to 86.60° (WIDE) After adjustment, tighten the tilting lock screws (x2)

36x Adjust the angular field of view and the focus. Adjust the angular field of view in accordance with the distance between the camera lens and

37IMPORTANT: • Do not move the focus ring. • Defocus may be caused by the reinstalled enclosure. In this case, perform the auto focus func-tion f

38c Attach the enclosure to the camera. Attach the cutout part of the main unit to the grooved part of the enclosure.IMPORTANT: • Securely tigh

39Configure the network settingsConfiguring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with def

4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

40c Select the camera you want to configure, and click [Access Camera].Note: • When cameras are displayed in [Panasonic IP Setting] screen, click th

41Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and tr

42• BasicPower source: 12 V DC, PoE (IEEE802.3af compliant)Power consumption: SW55912 V DC: 850 mA, PoE 48 V: 180 mA (Class 0 devices) SW55812 V DC:

43• CameraImage sensor: 1/3-type MOS image sensorEffective pixels: Approx. 3.1 megapixelsScanning area: 4.51 mm (H) × 3.38 mm (V) {3/16 inches (H)

44• LensZoom ratio: 3.6x Extra optical zoom: 10.8x (Imaging mode: 2 megapixel, under 640x360 resolution)Focal length: 2.8 mm - 10 mmMaximum apertur

45Transmission the image cut out: 2 megapixel [16:9] H.264 640x360/ 320x180 max.30 fps MJPEG 640x360/ 320x180 max.30 fps 1.3 megapixel [

46Installation Guide (this document) ...1 setWarranty card ...

47

Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying docu

5Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMI

6The network camera WV-SW559/WV-SW558 is designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (sheltere

7About the user manualsThere are 2 sets of operating instructions for the WV-SW559, WV-SW558 as follows. • Installation Guide: Explains how to inst

8IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inopera

9Network securityAs you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of i