Panasonic SC-HTB880 Manuel d'utilisateur télécharger pdf (Page 26)

RQT9903

Referenc e

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or

if the solutions indicated in the following guide do not

solve the problem, refer to “Customer Services

Directory (United States)” on page 32 if you reside in

the U.S.A. or refer to “Limited Warranty (ONLY FOR

CANADA)” on page 33 if you reside in Canada.

No power.

≥ Unplug the AC power supply cord for 10 sec

before plug in again.

≥ After turning the main unit on, if the main unit

immediately turns off, unplug the AC power

supply cord and consult your dealer.

≥

If the main unit does not turn on by turning on TV

(HDAVI control), manually turn on the main unit.

If the problem persists, refer to “HDMI” in

“Troubleshooting”.

The remote control does not work properly.

≥ The battery is dead. Replace the battery with a

new one. (> p. 8)

≥

It is possible that the insulation sheet has not been

removed. Remove the insulation sheet. (

p. 8)

≥ It may be necessary to set the code of the

remote control again after changing the battery

of the remote control. (> p. 20)

≥ Use the remote control within the correct

operation range. (> p. 8)

The main unit is automatically switched to

standby mode.

“AUTO POWER DOWN” function is on.

The main unit will automatically switch to standby

mode when no signal is input and no operation is

performed for approximately 20 minutes. Refer to

page 24 to turn this function off.

The main unit is turned off when the TV’s

speakers are selected in the speaker control.

This is a normal feature when using VIERA Link

(HDAVI Control 4 or later). Please read the

operating instructions for the TV for details about

its power save feature. (> p. 25)

The switches on the main unit do not work.

[Í/I], [j VOL i], [INPUT], and [ ] on the main

unit are touch keys. Touch the switches with your

finger. They may not work if operated with your

fingernails or hands wearing gloves.

This system does not operate correctly.

If the HDMI cable is connected to the wrong

terminal (HDMI AV IN1, HDMI AV IN2 or HDMI AV

OUT), this system will not operate correctly. Turn

the main unit off, disconnect the AC power supply

cord and reconnect the HDMI cable(s). (

p. 9, 10)

VIERA Link related operations no longer

function properly.

≥

Check the VIERA Link setting on the connected devices.

jTurn on VIERA Link function on the

connected devices.

jSelect this system as the speaker in the TV's

VIERA Link menu.

≥

Check if the VIERA Link settings are off. (

p. 24)

≥

When the HDMI connections are changed, after a power

failure or after the AC power supply cord has been

removed, VIERA Link operations may not function properly.

Turn on all the devices that are connected to the

TV with an HDMI cable and then turn the TV on.

jTurn off the VIERA Link settings of the TV and

turn it on again. For details refer to the

operating instructions for the TV.

jWhile the main unit and the TV are connected

with the HDMI cable, turn on the TV and then

remove the main unit’s AC power supply cord

and reconnect it again.

The first few seconds of audio cannot be

heard when using the HDMI connection.

This may occur during DVD-Video chapter

playback. Change the digital audio output setting on

the connected device from “Bitstream” to “PCM”.

When operating an HDMI compatible device of a different

brand, the main unit reacts in an unwanted manner.

HDAVI Control commands may use a different

signal depending on the brand of the device. In

this case, turn VIERA Link off. (> p. 24)

To return to the factory defaults.

While the main unit is on, touch and hold [Í/I] on

the main unit for more than 4 sec.

(“RESET” is indicated on the display when this

system is reset.)

If this system does not operate as expected, returning the

settings to the factory defaults may solve the problem.

≥ The remote control code will return to

“REMOTE 1” when this system is returned to

the factory preset. To change the remote

control code, refer to page 20.

General operation

HDMI

SC-HTB880PP_RQT9903-Y.book 26 ページ２０１４年５月８日　木曜日　午後６時１３分

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Commentaires sur ces manuels

Pas de commentaire

Panasonic SC-HTB880 Manuel d'utilisateur Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Panasonic SC-HTB880